compressed air system with a PCM heat exchanger prototype by Dr. Reza Alizade Evrin from Ontario Tech University.[1][2]
Compressed air system with a PCM heat exchanger prototype diagram

A compressed-air car is a compressed-air vehicle powered by pressure vessels filled with compressed air. It is propelled by the release and expansion of the air within a motor adapted to compressed air. The car might be powered solely by air, or combined (as in a hybrid electric vehicle) with other fuels such as gasoline, diesel, or an electric plant with regenerative braking.

Compressed-air cars utilize a thermodynamic process. Air cools when expanding and heats when compressed. Thermal energy losses in the compresser and tankage reduce the capacity factor of compressed air systems.

In 2020, Dr. Reza Alizade Evrin of Ontario Tech University developed an isothermal compressed air vehicle.[1][2] This prototype used low pressure air tanks and exhaust air recovery to power a paraffin heat exchanger system. Its energy efficiency reached 74%. This is as much as 90% of the efficiency of lithium-ion electric cars. It had a driving range of 140 km. Efficiency and range might be increased by a number of practical improvements. For example, combining the storage tank into the car chassis, higher pressure tanks, new rotary engines, and a more efficient heat exchanger. Also, the weight and cost of tanks and pneumatic parts might be reduced by using recycled and bio-based thermoplastics.

This technology might develop into an inexpensive green transportation technology. The energy, vehicles and compressors might be easily produced by decentralized methods, even circular industry. Using the plastics might permit open source fabrication using numerical control, including additive manufacturing. The compressed air for such vehicles might be easily produced by common forms of renewable energy. For example, multistage air compressors and intercoolers or hydraulic pumps might be attached directly to trompes, hydropower, VAWT wind turbines or stirling engines using a solar concentrator. Direct mechanical compression avoids the Carnot inefficiencies of heat engines. Insulated storage of compressed air avoids energy conversion and battery storage. Heat-based systems might utilize tankage of solar-heated molten salts driving a heat exchanger rather than an onboard heat recovery system. Electric energy, electric grids and their issues might be avoided.

Tech

Engines for compressed air

Dipietro eccentric shaft, rotary vane air engine

There have been several dubious claims with undisclosed information. The "di pietro" engine has been partially tested with CAD and finite element analysis programs. The results were published by Jarosław Zwierzchowski from Lodz University of Technology in 2017.[3] This motor is an eccentric shaft vane motor that uses low air pressure.

Compressed air tanks and collision safety

Hyundai nexo high pressure hydrogen tank safety
DuraStor consortium Thermoplastic composite pressure vessels for hydrogen vehicles [4]

The tanks must be designed to safety standards for a pressure vessel. ISO 11439 is a similar standard, for compressed natural gas tanks.[5]

The air storage tanks usable in compressed air cars can be low pressure (9 atm) or high pressure (240+ atm). Thus, they can be made of composite materials like thermoplastics and fiber reinforced thermoplastics,[4][6] This might permit low priced tankage. It might be made by rotational molding. Such tanks can be much lighter than lithium-iron batteries and 70% lighter than steel tanks. They resist rust from air, water and condensation. They last longer with less maintenance.

To reduce car weight further the pressure vessels can be used as structural parts of the chassis. Advanced 700-atmosphere pressure vessels have been developed for hydrogen cars. Crash tests showed good safety. Fiber reinforced thermoplastic tanks only rupture in collisions. They do not shatter or explode.[7]

Hydrogen tanks require ‘high strength’ to prevent rupture and ‘high stiffness’ for durability. Strength resists an external force. Stiffness maintains a shape. Carbon fiber hydrogen fuel tanks are as light as plastic but six times the strength of steel and four times the stiffness. “When a bullet penetrates a hydrogen tank, it does not explode. Instead, hydrogen leaks out through the bullet hole. In a standard collision test, not even a tiny amount of hydrogen was detected because none had leaked out."[7]

Compressed air production and storage

Wind Turbine Air Compressor posted Fieldlines.com: The Otherpower discussion board [8]
wind turbine powered hydraulic pump with Open Accumulator for Isothermal Compressed Air Energy Storage ICAES System [9]

Compressed air can also be produced by attaching an air compressor or hydraulic pump to a wind turbine [8][9] or by using a river, tidal or wave hydropower turbine. These all convert directly from mechanical to pneumatic energy. Eliminating electricity from the loop gives higher efficiency overall. It is also possible to use thermal solar energy with a parabolic or Fresnel lens solar concentrator to power a thermal Stirling engine. This can move the compressor or pump. Solar Stirling is more efficient than solar steam or photovoltaic.

Emissions

Compressed air cars are emission free. They also do not require a connection to the electric grid. A wind turbine or other renewable energy source can directly drive an air compressor or hydraulic pump. Compressed air cars do not rely on petrol stations or an electric grid. While centralized infrastructure might not be needed, it is an option. Tankage can be directly shipped, or a pipeline can be utilized.Compressed air is normally filtered to protect the compressor machinery. Therefore, discharge air has very little suspended dust. There may be some lubricants emitted by some systems, but further development might reduce this with oil free compressors and intercoolers

Resource consumption

Composite pressure vessels and pneumatic components could permit compressed air cars to be a circular industry. The materials would have to be biobased or recycled. Electric energy is not used, so there is no need for metals like copper, iron in magnets, etc.

Advantages

There can be a single conversion of mechanical energy to pneumatic or hydraulic energy.[9] Therefore, compressed air can have high energy efficiency when using mechanical renewable energy such as wind turbines or hydropower. Thermal energy to mechanical energy conversion is possible, but less efficient due to Carnot conversion inefficiencies. Thermal storage of heat from a renewable solar source is also possible using a phase change material such as a molten salt.

Energy efficiency of the 2020 isothermal prototype vehicle was 59.4% of a lithium-ion vehicle.[1][2]

Compressed air technology adapts to renewable energy and possibly a circular economy, if biobased or recycled composites can be used. Thus it is more sustainable than electric cars. For example, there is much less use of metals, or toxic battery chemistries. A centralized manufacturing and electric grid might be less necessary.

Efficiency is also helped by the low weight of composite pressure vessels relative to steel tanks or lithium-ion batteries.[6] Weight might be further reduced if the tanks support the car chassis. Pneumatic engines also have lower weights than electric engines.

Refueling is possible in many places using only wind, solar power or hydropower to move an air compressor, hydraulic pump or Stirling engine.

Pneumatic power has energy synergy, because it is well suited to automotive mechatronics. Many car systems can be powered by small air motors. For example, active pneumatic suspension, pneumatic steering, or pneumatic shock absorbers.[10] Expansion of the compressed air creates cold temperatures, and can directly provide air conditioning or climate control.

Energy recovery systems with regenerative suspension and regenerative braking produce low pressure compressed air. This can be stored in a pressure vessel.

Pistonless engines using compressed air are very quiet.[11]

There is no fire hazard after accidents, unlike systems that utilize combustion fuels or high power batteries.

Compressed air engines reduce the cost of car production, because there is no need to build a cooling system, spark plugs, starter motor, or mufflers.

The rate of self-discharge is very low compared to batteries. A fueled, compressed-air vehicle may be left unused for a longer time than an electric car.

They reduce or eliminate hazardous chemicals such as gasoline, battery acids and related metals such as lead.

Compressed air cars are safer in more situations:

  • potentially explosive work atmospheres
  • brush-fire areas
  • the vicinity of strong magnetic electric fields
  • radio quiet zones

Disadvantages

Compressed air has a lower Energy density than liquid nitrogen or hydrogen.

They have less energy efficiency and range than gas turbines, internal combustion engines or battery vehicles. However the production of compressed air is more energy efficient and so requires less wind power and infrastructure per unit of energy.

While batteries somewhat maintain their voltage throughout their discharge and chemical fuel tanks provide the same power densities from the first to the last litre, the pressure of compressed air tanks falls as air is drawn off. There are mechanical methods (e.g. continuously variable transmissions or auxiliary motors) to reduce this effect, but they add expense.

Developers and manufacturers

Various companies are investing in the research, development and deployment of compressed air cars. The MDI Air Car made its public South African debut in 2002.[12] It was predicted to be in production "within six months" in January 2004.[13] As of 2022, it was not in production.

MDI

MDI has proposed a range of vehicles made up of AIRPod, OneFlowAir, CityFlowAir, MiniFlowAir and MultiFlowAir.[14] One of the main innovations of this company is its implementation of its "active chamber", which is a compartment which heats the air (through the use of a fuel) in order to double the energy output.[15] This 'innovation' was first used in torpedoes in 1904.

Tata Motors

As of January 2009, Tata Motors of India had planned to launch a car with an MDI compressed air engine in 2011.[16][17] In December 2009 Tata's vice president of engineering systems confirmed that the limited range and low engine temperatures were causing problems.

Tata Motors announced in May 2012[18] that they have assessed the design past phase 1, the "proof of the technical concept", and were proceeding to full production for the Indian market. Tata moved to phase 2, "completing detailed development of the compressed air engine into specific vehicle and stationary applications".[19]

In February 2017, Dr. Tim Leverton, president and head at Advanced and Product Engineering at Tata revealed that the project was "starting industrialisation" with the first vehicles to be available by 2020.[20] Other reports indicate Tata is also reviving plans for a compressed air version of the Tata Nano,[21] This had previously been under consideration as part of their collaboration with MDI.[22]

Engineair Pty Ltd

Engineair is an Australian company. It produced prototypes of small vehicles using a rotary air engine designed by Angelo Di Pietro. The company is seeking commercial partners to utilise its engine.[23]

Peugeot/Citroën

Peugeot and Citroën announced that they intended to build a car using compressed air as an energy source. However, it utilizes a hybrid system. A gasoline engine propels the car over 70 km/h or when the compressed air tank has been depleted.[24][25]

In January 2015, there was disappointing news from France: PSA Peugeot Citroën has put an indefinite hold on the development of its promising-sounding Hybrid Air powertrain, apparently because the company has been unable to find a development partner willing to split the huge costs of engineering the system. Development costs are estimated to 500 million Euros. Production volumes would have to be more than 500,000 cars a year to repay these costs.[26] The head of the project left Peugeot in 2014.[27]

APUQ

APUQ (Association de Promotion des Usages de la Quasiturbine) has made the APUQ Air Car, a car powered by a Quasiturbine.[28]

See also

References

  1. 1 2 3 "Compressed air cars for urban transportation". advancedsciencenews. 7 September 2020. Retrieved 2020-09-07.
  2. 1 2 3 Evrin, Reza Alizade; Dincer, Ibrahim (2020). "Experimental investigation of a compressed air vehicle prototype with phase change materials for heat recovery". Energy Storage. onlinelibrary.wiley. 2 (5). doi:10.1002/est2.159. S2CID 219020514. Retrieved 2020-04-27.
  3. "Design type air engine Di Pietro". 2017-07-18. Retrieved 2017-10-13.
  4. 1 2 "Thermoplastic composite pressure vessels for FCVs". compositesworld.com. 2015-02-01. Retrieved 2015-02-01.
  5. "Gas cylinders – High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles". Iso.org. 2006-07-18. Retrieved 2010-10-13.
  6. 1 2 "High pressure gas tanks in thermoplastic composites". plastics.gl. 2014-05-01. Retrieved 2014-05-01.
  7. 1 2 "OHydrogen Tank: Safety Proven (OA-ICAES) System". hyundaimotorgroup. Retrieved 2019-07-13.
  8. 1 2 "Wind Turbine Air Compressor". Retrieved 2015-07-13.
  9. 1 2 3 "Open Accumulator Isothermal Compressed Air Energy Storage (OA-ICAES) System". Retrieved 2018-07-13.
  10. "Automated Pneumatic Bumper For Vehicle Safety". 2012-05-01. Retrieved 2014-05-01.
  11. "Pumping up the silent engine | GE News".
  12. Kevin Bonsor (2005-10-25). "How Air-Powered Cars Will Work". HowStuffWorks. Retrieved 2006-05-25.
  13. Robyn Curnow (2004-01-11). "Gone with the wind". The Sunday Times (UK). London. Retrieved 2006-05-25.
  14. Learn everything about the compressed air cars! Archived 2013-05-20 at the Wayback Machine.
  15. "MDI's active chamber". Thefuture.net.nz. Archived from the original on 2011-05-07. Retrieved 2010-12-12.
  16. "Tata Air Car to drive in by 2011". Popular Mechanics. Archived from the original on 2010-02-10.
  17. "An engine which uses air as fuel: Tata Motors and technology inventor, MDI of France, sign agreement" (Press release). Tata Motors. February 5, 2007. Archived from the original on March 14, 2012. Retrieved June 14, 2012.
  18. "MDI's air engine technology tested on Tata Motors vehicles" (Press release). Tata Motors. May 7, 2012. Archived from the original on May 9, 2013. Retrieved June 14, 2012.
  19. Tata Motors enters second phase of air-car development Gizmag.com, 2012-05-07
  20. "Tata Motors' air-powered car project still on, to be launch ready in 3 years". Auto Car Professional. Retrieved 24 August 2017.
  21. "Tata Nano could spawn electric, hybrid & air-powered variants – Report". Indian Autos Blog. Jan 25, 2017. Retrieved 23 August 2017.
  22. "Nano was to run on air, battery but Ratan Tata couldn't implement plans". Hindustan Times. Oct 28, 2016. Retrieved 23 August 2017.
  23. Matt Campbell (November 3, 2011). "The motorbike that runs on air". Sydney Morning Herald. Archived from the original on November 5, 2011. Retrieved 2011-11-07.
  24. "Compressed-Air Hybrid Car Developed". Gas2.org. 2013-02-18. Retrieved 2013-09-08.
  25. Marc Carter. "Peugeot Announces Plans to Release a Hybrid Car That Runs on Compressed Air by 2016". Retrieved 30 May 2015.
  26. Duff, Mike (January 26, 2015). "Deflated: Peugeot Citroen Shelves Its Air Hybrid Technology". Car and Driver. Retrieved 2018-10-29.
  27. Fansilber, Maxime Amiot Denis (November 1, 2015). "PSA : la révolution de l'Hybrid Air n'aura pas lieu". Les Echos (in French). Retrieved 2018-10-29.
  28. "Association de Promotion des Usages de la Quasiturbine". APUQ. Archived from the original on 2016-03-04. Retrieved 2012-01-26.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.