Pennsylvania Railroad N1s
PRR N1s #7246 at Youngstown, Ohio in 1919, when less than a year old. Note the Lines West central headlight (later relocated higher) and high slope-sided tender coal space
Type and origin
Power typeSteam
BuilderALCO-Brooks (35),
Baldwin Locomotive Works (25)
Build date1918–1919
Total produced60
Specifications
Configuration:
  Whyte2-10-2
  UIC1'E1'h2g
Gauge4 ft 8+12 in (1,435 mm)
Leading dia.33 in (0.838 m)
Driver dia.62 in (1.575 m)
Trailing dia.36 in (0.914 m)
WheelbaseLocomotive: 41 ft 11+12 in (12.79 m)
Length91 ft 4+58 in (27.85 m)
Axle load75,600 lb (34,300 kg; 34.3 t)
Adhesive weight351,000 lb (159,000 kg; 159 t)
Loco weight435,000 lb (197,000 kg; 197 t)
Tender weightEmpty: 86,800 lb (39,400 kg; 39.4 t);
Loaded: 206,100 lb (93,500 kg; 93.5 t)
Tender type100 F 85
Fuel typeCoal
Fuel capacity39,300 lb (17,800 kg; 17.8 t)
Water cap.9,600 US gal (36,000 L; 8,000 imp gal)
Firebox:
  Grate area79.9 sq ft (7.4 m2)
Boiler pressure215 psi (1.48 MPa)
CylindersTwo
Cylinder size30 in × 32 in (762 mm × 813 mm)
Valve gearWalschaerts
Valve typePiston
Performance figures
Maximum speed35 mph (56 km/h)
Tractive effort84,890 lbf (377.61 kN)
Factor of adh.4.13
Career
LocaleMidwest (Illinois Indiana, Ohio)
Retiredby 1950
DispositionAll scrapped

The Pennsylvania Railroad's N1s was a class of steam locomotive built for Lines West. They were of 2-10-2 "Santa Fe" wheel arrangement, ten driving wheels with a two-wheel leading truck and a two-wheel cast KW-pattern trailing truck under a giant firebox. This arrangement was well suited to the N1s' intended purpose, which was as a heavy drag freight engine for coal and iron ore traffic to and from lakeside ports. The design was developed by the PRR's Fort Wayne Shops and orders were placed with Alco (Brooks) (35 locomotives) and Baldwin (25 locomotives) for a total of 60; the first Alco locomotive was delivered in December 1918, with the remainder arriving during 1919.

PRR N1s #8363 in its official builders' photo.

The N1s was a large locomotive; the boiler was the largest then used on any non-experimental PRR locomotive, with a large Belpaire firebox with 79.9 square feet (7.4 m2) of grate area and a 5-foot (1.52 m) long combustion chamber. No feedwater heater was fitted, but a mechanical stoker and power reverse were, necessities on such a large locomotive. Boiler pressure was 215 pounds per square inch (1.48 MPa), although it was designed to take a pressure of 250 psi (1.72 MPa).

To allow the locomotive to negotiate tight 23-degree curves, the first and fifth driving axles were fitted with lateral motion devices and the center axle was blind.

In many respects, the N1s was similar in ability to the I1s 2-10-0 "Decapod". Driver diameter, weight on drivers and cylinder size were almost identical. The N1s' boiler was larger, but of a lower pressure. The I1s' tractive effort was a little higher, while the N1s had a superior factor of adhesion. The N1s, as a low speed drag hauler, was limited to 35 mph (56 km/h), while the I1s was capable of 50 mph (80 km/h) or greater.

The N1s were the first class of large power withdrawn after diesel locomotives appeared; all were gone by 1950, and none were saved for display. Their task, low speed drag haulage, was the diesel locomotive's forte.

References

    This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.