A creep-testing machine measures the alteration of a material after it has undergone stresses.

Engineers use Creep machines to determine the stability and behaviour of a material when put through ordinary stresses.[1] They determine how much strain (load) an object can handle under pressure, so engineers and researchers are able to determine what materials to use.

The device generates a creep time-dependent curve by calculating the steady rate of creep in reference to the time it takes for the material to change.

Creep

Creep is the tendency of a material to change form over time after facing high temperature and stress. Creep increases with temperature and it is more common when a material is exposed to high temperatures for a long time or at the melting point of the material.

Creep machines are used to understand the creep of materials and determine which type can do the job better, which is important when making and designing materials for everyday uses. They most commonly test the creep of alloys and plastics for the understanding of their properties and advantages of one material's use over another.[2]

Background

Creep testing machine

The first creep testing machines were created in 1948 in Britain to test materials for aircraft to see how they would stand in high altitudes, temperature and pressure.[3] The machines were first developed to further calculate and understand the steady rate of creep in materials.

Design

Researchers look to test objects with a creep machine to understand the process of metallurgy and the physical mechanical properties of a metal, test the development of alloys, receive data from the loads that are derived and to find out whether a sample or material is within the boundary of what they are testing.[3] The basic design of a creep machine is the furnace, loading device and support structure.

The main type of creep testing machine is a constant load creep testing machine. The constant load creep machine consists of a loading platform, foundation, fixture devices and furnace. The fixture devices are the grips and pull rods.[4]

  • Load platform or load hanger is where the object will endure pressure at a constant rate.
  • Grips hold the material in a certain position. Position is important because if the alignment is off, the machine will deliver inaccurate creep readings.
  • Dial Gauge is used to measure the strain. It is the object that captures the movement of the object in the machine. The load beam transfers the movement from the grip to the dial gauge.
  • Heating Chamber is what surrounds the object and maintain the temperature.

Applications

Creep machines are most commonly used in experiments to determine how efficient and stable a material is. The machine is used by students and companies to create a creep curve on how much pressure and stress a material can handle. The machine is able to calculate the stress rate, time and pressure.

Creep testing has three different applications in the industry:

  1. Displacement-Limited applications : the size must be precise and there must be little errors or tendency to change. This is most commonly found in turbine rotors in jet engines.
  2. Rupture Limited applications: in this application the break cannot occur to the material but there can be various dimensions as the material goes through creep. High pressure tubes are examples of them.
  3. Stress relaxation limited application : the tension at the beginning becomes more relaxed and the tension will continue to relax as the time goes by, such as cable wires and bolts.[5]

Graphing of creep

Creep is dependent on time so the curve that the machine generates is a time vs. strain graph. The slope of a creep curve is the creep rate dε/dt The trend of the curve is an upward slope. The graphs are important to learn the trends of the alloys or materials used and by the production of the creep-time graph, it is easier to determine the better material for a specific application.

Stages of creep

There are three stages of creep:

  • Primary Creep: the initial creep stage where the slope is rising rapidly at first in a short amount of time. After a certain amount of time has elapsed, the slope will begin to slowly decrease from its initial rise.
  • Steady State Creep: the creep rate is constant so the line on the curve shows a straight line that is a steady rate.
  • Tertiary Creep: the last stage of creep when the object that is being subjected to pressure is going to reach its breaking point. In this stage, the object's creep continuously increases until the object breaks. The slope of this stage is very steep for most materials.

By examining the three stages above, scientists are able to determine the temperature and interval in which an object will be disturbed once exposed to the load. Some materials have a very small secondary creep state and may go straight from the primary creep to the tertiary creep state. This is dependent on the properties of the material that is being tested. This is important to note because going straight to the tertiary state causes the material to break faster from its form.[6]

A linear graph denotes that the material under stress is gradually deforming, and this would be harder to track at what level of stress an object can handle. This would also mean that the material would not have distinct stages, which would make an object's breaking point less predictable. This is a disadvantage to scientists and engineers when trying to determine the level of creep the object can handle.[7]

References

  1. ↑ Kalkhouran, Abbas Aghajani (2017-01-17). A Creep Testing Machine: Second Edition. LAP LAMBERT Academic Publishing. ISBN 978-3-330-02611-7.
  2. ↑ W. Blum, Materials Science and Engineering: A; Volumes 319-321, December 2001, pg.735-740
  3. 1 2 A. I. Smith, D. Murray, M. F. Day, "Creep Testing Equipment-Design Features and Control"; Volume 180 Pt. 3A, 1965-66, pg.303-307
  4. ↑ J.B. Grishaber,"A Novel Computer Controlled Constant Stress Lever Arm Creep Testing Machine", Review of Scientific Instruments; Jul97, Vol. 68 Issue 7, pg.2812
  5. ↑ Dr. Sabbah Ataya, "Creep Testing Machines", 2008, http://www.slideshare.net/ea2m/creep-testing-machines-presentation
  6. ↑ Experiment 4 Lab, Center for Reliability of Ceramics, Department of Mechanical Engineering, University of Houston, "Archived copy" (PDF). Archived from the original (PDF) on 2004-12-01. Retrieved 2011-10-19.{{cite web}}: CS1 maint: archived copy as title (link)
  7. ↑ Narayana, V. J. S., K. Balasubramaniam, and R. V. Prakash. "Detection And Prediction Of Creep-Damage Of Copper Using Nonlinear Acoustic Techniques." AIP Conference Proceedings 1211.1,2010, pg.1410-1417
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.