2012

In 2012, the KTM 500 EXC received a significant update. Both the power unit and transmission were redesigned from the ground up. Most notably however, it now featured the latest Keihin engine management system with electronic fuel injection, which now had the ability to compensate for altitude and temperature changes. Despite the change to fuel injection, the motor was now 2.49 KG lighter, more compact, and had less reciprocating mass. A new cylinder head featured newly designed intake and exhaust ports, with lightweight titanium valves being used on the intake side. A new, 15% lighter forged piston reduced reciprocating mass for increased durability at high engine speeds. New nitride-coated piston rings increased wear resistance. The combustion chamber had been redesigned and also received a new water jacket. A newly designed crankshaft featured a new ultra-light Pankl connecting rod, in combination with the lighter piston, helped keep vibration at a minimum. The balancer shaft was redesigned to be more compact, and also served as the drive for the water pump. New valve chain guides and a new spring-loaded mechanical chain tensioner with a ratchet stop were used for a simpler, lighter weight design. The engine now featured a common oil circuit with two oil pumps, abandoning the previous separate oiling of the motor and transmission seen on the 530. A pressure pump lubricated the engine, while a suction pump drew oil from the crankcase, using it to lubricate the transmission and the clutch. Cooling was improved by integrating the radiator hose routing into the frame, no longer impeding airflow behind the radiators. The cooling system also featured a new T-connector with improved flow and heat dissipation, and an auxiliary radiator fan was also fitted to improve cooling at low speeds. Cooling for the new, larger stator had also been improved, with oil-jet cooling to help cope with the increased electrical demand of the fuel injection system (196W up from 130W). The engine case was now 1.8 KG lighter than the outgoing XC4 motor, due in part to its more compact design, and the fact that it was now die-cast as opposed to being sand-cast as seen on previous models. Despite being lighter, the case was now considerably more impact resistant thanks to the use of a special high-ductility aluminium alloy. A newly developed DDS (damped diaphragm steel) clutch featured a billet steel basket with cushioning dampers, and made use of a 250 Nm Belleville spring washer for the first time instead of the customary conical springs, greatly reducing clutch operation force. Both the clutch master and slave were produced by Brembo. The frame was completely revamped, with a noted 30% increase in lateral stiffness, as well as a reduction in size afforded by the new more compact motor, which in turn also provided better ground clearance. A new, 300g lighter swingarm featured a more central mount for the linkless PDS (Progressive Damping System), allowing for the swingarm to be loaded more evenly. Suspension was also reworked, with a new 7mm longer WP PDS rear shock, and newly developed Teflon coated bushings and low-friction SKF oil and dust seals on the latest 48mm WP Open Cartridge forks. The wheelset featured black Giant rims with CNC machined hubs, mounted with Metzler Six Days Extreme tyres front and rear.

2013

In 2013, the KTM 500 EXC received only minor changes. Specially developed for KTM by MAXXIS, new tyres with increased longevity were fitted, alongside newly styled graphics for the bodywork.

2014

The 2014 model received a multitude of changes, most notably it featured all new bodywork inspired by the SX-F range. The front fender was now 50% stiffer than its predecessor, and accumulated much less mud thanks to a complete lack of ribbing. This new fender design required a redesign of the lower triple clamp. A new headlight and its surround were the result of four years of R&D, featuring greater light output from a smaller bulb, which enabled tidier and more crash-resistant wiring behind. Redesigned larger handguards were now made of an ultra-sturdy two-component plastic. The airbox was redesigned for greater capacity, better airflow and improved sealing. The air filter now featured a revised latch which secured the filter better than previous years. Firmer, yet thicker seat foam developed in conjunction with footwear giant Adidas provided a much-needed improvement in comfort for longer rides. The frame lost 300g of weight, due largely to thinner cradle tubing. The clutch was upgraded with a stronger 280 Nm Belleville spring washer (up from the initial 250 Nm seen in the 2012/2013 models). The front brake master cylinder was redesigned by Brembo to accommodate more-level mounting of the reservoir, eliminating the need to tilt the perch forward to fill the reservoir properly. A new 9mm piston (down from 10mm) was also employed to produce a noticeably more progressive brake feel, in combination with the new brake pad material. The chain guide was redesigned to be lighter without compromising on strength. An updated design of the fuel cap did away with the notoriously difficult to open caps of previous years, now being much easier to open. The thermo-switch for the auxiliary radiator fan was updated, due to the switch sometimes failing long term on 2012/2013 models. A new under-seat ECU mount and updated fuse box further refined the tidiness of the electrical system. A more powerful battery was also fitted, improving starting strength and reliability. The 2014 model also saw the introduction of a new wheelset, featuring new Takasago EXCEL AL7 rims, CNC machined alloy hubs, zinc/nickel coated spokes and lightweight aluminium nipples, reducing the overall weight of each wheel by 200g.

The KTM 500 EXC (2012–present) is a 50 state street legal dual-sport enduro dirtbike powered by a 510 cc SOHC engine.^[4][5]