For environmental remediation, Low-temperature thermal desorption (LTTD), also known as low-temperature thermal volatilization, thermal stripping, and soil roasting, is an ex-situ remedial technology that uses heat to physically separate petroleum hydrocarbons from excavated soils. Thermal desorbers are designed to heat soils to temperatures sufficient to cause constituents to volatilize and desorb (physically separate) from the soil. Although they are not designed to decompose organic constituents, thermal desorbers can, depending upon the specific organics present and the temperature of the desorber system, cause some organic constituents to completely or partially decompose. The vaporized hydrocarbons are generally treated in a secondary treatment unit (e.g., an afterburner, catalytic oxidation chamber, condenser, or carbon adsorption unit) prior to discharge to the atmosphere. Afterburners and oxidizers destroy the organic constituents. Condensers and carbon adsorption units trap organic compounds for subsequent treatment or disposal.

Some preprocessing and postprocessing of soil is necessary when using LTTD. Excavated soils are first screened to remove large (greater than 2 inches in diameter) objects. These may be sized (e.g., crushed or shredded) and then introduced back into the feed material. After leaving the desorber, soils are cooled, re-moistened to control dust, and stabilized (if necessary) to prepare them for disposal or reuse. Treated soil may be redeposited onsite, used as cover in landfills, or incorporated into asphalt.

Application

LTTD has proven very effective in reducing concentrations of petroleum products including gasoline, jet fuels, kerosene, diesel fuel, heating oils, and lubricating oils. LTTD is applicable to constituents that are volatile at temperatures up to 1,200 °F. Most desorbers operate at temperatures between 300 °F to 1,000 °F. Desorbers constructed of special alloys can operate at temperatures up to 1,200 °F. More volatile products (e.g. gasoline) can be desorbed at the lower operating range, while semivolatile products (e.g. kerosene, diesel fuel) generally need temperatures over 700 °F, and relatively nonvolatile products (e.g., heating oil, lubricating oils) need even higher temperatures. Essentially all soil types are amenable for treatment by LTTD systems. However, different soils may require varying degrees and types of pretreatment. For example, coarse-grained soils (e.g. gravel and cobbles) may require crushing; fine-grained soils that are excessively cohesive (e.g. clay) may require shredding.

State and local regulations specify that petroleum-contaminated soils must be pilot tested, by some soil from the site being processed through the LTTD system (a "test burn"). The results of preliminary testing of soil samples should identify the relevant constituent properties, and examination of the machine's performance records should indicate how effective the system will be in treating the soil. The proven effectiveness of a particular system for a specific site or waste does not ensure that it will be effective at all sites or that the treatment efficiencies achieved will be acceptable at other sites. If a test burn is conducted, it is important to ensure that the soil tested is representative of average conditions and that enough samples are analyzed before and after treatment to confidently determine whether LTTD will be effective.

Operation of LTTD units requires various permits and demonstration of compliance with permit requirements. Monitoring requirements for LTTD systems are by their nature different from monitoring required at a UST site. Monitoring of LTTD system waste streams (e.g. concentrations of particulates, volatiles, and carbon monoxide in stack gas) are required by the agency or agencies issuing the permits for operation of the facility. The LTTD facility owner/operator is responsible for complying with limits specified by the permits and for other LTTD system operating parameters (e.g. desorber temperature, soil feed rate, afterburner temperature).

The decision as to whether or not LTTD is a practical remedial alternative depends upon site-specific characteristics (e.g. the location and volume of contaminated soils, site layout). Practicability is also determined by regulatory, logistical, and economic considerations. The economics of LTTD as a remedial option are highly site-specific. Economic factors include:-

• Site usage (because excavation and onsite soil treatment at a retail site (e.g. gasoline station, convenience store) will most likely prevent the business from operating for a longish time).
• The cost of LTTD per unit volume of soil relative to other remedial options.
• The location of the nearest applicable LTTD system (because transportation costs are a function of distance).

Operation principles

Thermal desorption systems fall into two general classes—stationary facilities and mobile units. Contaminated soils are excavated and transported to stationary facilities; mobile units can be operated directly onsite. Desorption units are available in a variety of process configurations including rotary desorbers, asphalt plant aggregate dryers, thermal screws, and conveyor furnaces.

The plasticity of the soil is a measure of its ability to deform without shearing and is to some extent a function of water content. Plastic soils tend to stick to screens and other equipment, and agglomerate into large clumps. In addition to slowing down the feed rate, plastic soils are difficult to treat. Heating plastic soils requires higher temperatures because of the low surface area to volume ratio and increased moisture content. Also, because plastic soils tend to be very fine-grained, organic compounds tend to be tightly sorbed. Thermal treatment of highly plastic soils requires pretreatment, such as shredding or blending with more friable soils or other amendments (e.g. gypsum).

Material larger than 2 inches in diameter will need to be crushed or removed. Crushed material is recycled back into the feed to be processed. Coarser-grained soils tend to be free-flowing and do not agglomerate into clumps. They typically do not retain excessive moisture, therefore, contaminants are easily desorbed. Finer-grained soils tend to retain soil moisture and agglomerate into clumps. When dry, they may yield large amounts of particulates that may require recycling after being intercepted in the baghouse.

The solids processing capacity of a thermal desorption system is inversely proportional to the moisture content of the feed material. The presence of moisture in the excavated soils to be treated in the LTTD unit will determine the residence time required and heating requirements for effective removal of contaminants. In order for desorption of petroleum constituents to occur, most of the soil moisture must be evaporated in the desorber. This process can require significant additional thermal input to the desorber and excessive residence time for the soil in the desorber. Moisture content also influences plasticity which affects handling of the soil. Soils with excessive moisture content (> 20%) must be dewatered. Typical dewatering methods include air drying (if storage space is available to spread the soils), mixing with drier soils, or mechanical dewatering.

The presence of metals in soil can have two implications:

• Limitations on disposal of the solid wastes generated by desorption.
• Attention to air pollution control regulations that limit the amount of metals that may be released in stack emissions.

At normal LTTD operating temperatures, heavy metals are not likely to be significantly separated from soils.

High concentrations of petroleum products in soil can result in high soil heating values. Heat released from soils can result in overheating and damage to the desorber. Soils with heating values greater than 2,000 Btu/lb require blending with cleaner soils to dilute the high concentration of hydrocarbons. High hydrocarbon concentrations in the offgas may exceed the thermal capacity of the afterburner and potentially result in the release of untreated vapors into the atmosphere. Excessive constituent levels in soil could also potentially result in the generation of vapors in the desorber at concentrations exceeding the lower explosive limit (LEL). If the LEL is exceeded there is a potential for explosion.

System design

The term "thermal desorber" describes the primary treatment operation that heats petroleum-contaminated materials and desorbs organic materials into a purge gas. Mechanical design features and process operating conditions vary considerably among the various types of LTTD systems. Desorption units are: available in four configurations:

1. Rotary dryer
2. Asphalt plant aggregate dryer
3. Thermal screw
4. Conveyor furnace

Although all LTTD systems use heat to separate (desorb) organic contaminants from the soil matrix, each system has a different configuration with its own set of advantages and disadvantages. The decision to use one system over another depends on the nature of the contaminants as well as machine availability, system performance, and economic considerations. System performance may be evaluated on the basis of pilot tests (e.g., test burns) or examination of historical machine performance records. Pilot tests to develop treatment conditions are generally not necessary for petroleum-contaminated soils.

Offgas treatment

Offgas treatment systems for LTTD systems are designed to address three types of air pollutants: particulates, organic vapors, and carbon monoxide. Particulates are controlled with both wet (e.g., venturi scrubbers) and dry (e.g., cyclones, baghouses) unit operations. Rotary dryers and asphalt aggregate dryers most commonly use dry gas cleaning unit operations. Cyclones are used to capture large particulates and reduce the particulate load to the baghouse. Baghouses are used as the final particulate control device. Thermal screw systems typically use a venturi scrubber as the primary particulate control.

The control of organic vapors is achieved by either destruction or collection. Afterburners are used downstream of rotary dryers and conveyor furnaces to destroy organic contaminants and oxidize carbon monoxide. Conventional afterburners are designed so that exit gas temperatures reach 1,400 °F to 1,600 °F. Organic destruction efficiency typically ranges from 95% to greater than 99%.

Condensers and activated carbon may also be used to treat the offgas from thermal screw systems. Condensers may be either water-cooled or electrically cooled systems to decrease offgas temperatures to 100 °F to 140 °F. The efficiency of condensers for removing organic compounds ranges from 50% to greater than 95%. Noncondensible gases exiting the condenser are normally treated by a vapor-phase activated carbon treatment system. The efficiency of activated carbon adsorption systems for removing organic contaminants ranges from 50% to 99%. Condensate from the condenser is processed through a phase separator where the non-aqueous phase organic component is separated and disposed of or recycled. The remaining water is then processed through activated carbon and used to rehumidify treated soil.

Treatment temperature is a key parameter affecting the degree of treatment of organic components. The required treatment temperature depends upon the specific types of petroleum contamination in the soil. The actual temperature achieved by an LTTD system is a function of the moisture content and heat capacity of the soil, soil particle size, and the heat transfer and mixing characteristics of the thermal desorber.

Residence time is a key parameter affecting the degree to which decontamination is achievable. Residence time depends upon the design and operation of the system, characteristics of the contaminants and the soil, and the degree of treatment required.

References