The Marui Big Bear Datsun (MT-59-RC-4) was an early 1/12-scale electric "monster truck" radio controlled car manufactured and distributed by Japanese hobby and airsoft gun manufacturer Tokyo Marui.

Background

Originally sold only through mail order in 1984 as a kit without batteries, radio and charger, the Big Bear featured a plastic, tub-styled chassis, Mabuchi M480-RS motor, mechanical speed control and live axle rear suspension as opposed to an independent setup. Tires were wide, chevron-treaded implement-styled units and actually comprised the majority of the Big Bear's suspension. The shock absorbers were simple coilover units which allowed for limited suspension travel. Coil springs also served to hold the front bumper in place and absorb impact. The body was a highly detailed styrene plastic Datsun pickup with driver figure and "Big Bear" decal set.

Because of its low cost, ease of assembly and good factory and aftermarket support, the Big Bear played an important role in the early growth of the radio control hobby. Due to intense competition from Tamiya and somewhat brittle plastic, Tokyo Marui pulled completely out of the hobby market by the end of the decade.

The 'Big Bear' was sold in Australia as a complete kit, including radio transmitter, batteries, and charger.[1]

Kit Revisions

Owners of the original version (v.1) of the Big Bear experienced problems with its differential gears. This kit used the same gearboxes and gears as the Marui Jeep CJ (MT-59-RC-7) and the Marui Toyota Landcruiser (MT-59-RC-8) kits and consisted of 2 large bevel gears, and a gear set of 48 pitch metric. This proved to be a major problem for the first version of the Big Bear, as the special black M480RS motor and the large tires designed for the Big Bear created increased load, causing the differential gears to break or heat up and melt.

Marui made a special replacement part "#048 - Strengthened Differential Gear Set" that consisted of a tri-bevel differential, larger 32 pitch gears, and a change to the gear ratios. This new differential gear set found its way into the re-release of the Big Bear (v.2) coupled with a new heat sink plate between the gearbox halves. There were some draw backs to the new gears; The added torque of the new gear ratios made the truck do wheelies more easily, and made the truck a little slower. In addition to replacement gears and heat sink, Marui replaced the original M480-RS motor with an RS540-SH motor, and a redesigned mechanical speed controller with covered contacts to eliminate contamination.

Specifications

  • Scale: 1/12
  • Chassis construction: ABS resin tub-style
  • Transmission: Rear wheel drive with differential
  • Suspension: Independent front trailing arm and live axle rear suspension
  • Shock absorbers: Simple coilover
  • Motor: Mabuchi RS-540 (v.1) / RS-540SH (v.2)
  • Tires: Semi-pneumatic rubber chevron
  • Original Marui catalog number: MT-59-RC-4

Spare Parts List

The following Marui RC Parts were used for the Big Bear, as well as other Marui kits:

Part # Description
#007 GEAR & MOTOR CASE
#010 OILLESS BEARING SET
#014 CONTROLLER SET (the original speed controller for v.1)
#016 CONNECTOR SET
#021 SERVO SAVER SET
#028 DIFFERENTIAL GEAR SET (the original gear set for v.1)
#029 PINION SEAR SET
#030 FRONT ARM SET
#031 REAR ARM SET
#032 REAR AXLE SET
#033 BUSHING SET
#035 FRONT TIRE & WHEEL SET
#036 REAR TIRE & WHEEL SET
#037 BUMPER SET
#038 ADJUSTER
#047 CONTROLLER SET (the new and improved speed controller for v.1)
#048 STRENGTHENED DIFFERENTIAL GEAR SET (the new and improved gear set for v.2)
M060 CHASSIS
M096 WINDSHIELD-BB
M097 ROLL BAR
M098 SEAT-BB
M099 BODY-BB
M132 IDLER GEAR
M133 BODY MOUNT

Aftermarket Parts

Many supporting manufacturers developed products for the Big Bear. Here is a list of known aftermarket parts designed specifically for this kit:

Manufacturer Part # Description
BO-LINK BODY MOUNTING KIT
BO-LINK FORD VAN BODY FOR BIG BEAR
BRU-LINE 4202 SUPER SYSTEM REAR HUB - BIG BEAR
BRU-LINE 5278 BIG BEAR BODY MOUNTING KIT
IMEX DAWG TIRES FOR BIG BEAR
MOORE'S IDEAL PRODUCTS (MIP) BBG HEAVY DUTY GEAR SET FOR BIG BEAR
MOORE'S IDEAL PRODUCTS (MIP) BIG BEAR BALL DIFFERENTIAL GEAR
MOORE'S IDEAL PRODUCTS (MIP) CASE SAVER
MOORE'S IDEAL PRODUCTS (MIP) IDLER SHAFT
MOORE'S IDEAL PRODUCTS (MIP) TEFLON AXLE BUSHINGS
PRO-LINE 2512 CHROME HUBS (FRONT)
PRO-LINE 2513 CHROME HUBS (REAR)
RACE MASTER 701 BIG BEAR WHEELIE BAR

References

  1. "Archived copy". Archived from the original on 2012-03-24. Retrieved 2011-05-19.{{cite web}}: CS1 maint: archived copy as title (link)


This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.